Table of Contents
Why is my Salus receiver flashing red?
Description : A red flashing light on your Receiver means that the communications link between your Thermostat and Receiver has been lost and your devices need pairing. Your Thermostat will be failing to control your boiler and your heating will not be working.
How do I pair a Salus thermostat with a receiver?
How do I reset my Salus wireless thermostat?
The Backlight Liquid Crystal Display (LCD) gives a highly visible, easily readable indication of the programmable thermostat status. Press the buttons together for 3 sec. Press Up or Down to select the hour format. After power up, the thermostat is reset.
How do you test a Salus thermostat?
How do I fix my Salus thermostat?
Why is my thermostat flashing red?
Possible Causes for a Red Flashing Light
High Pressure or High Temperature Switch is On. Low Pressure or Low Temperature Switch is On. Low Discharge Temperature. Liquid Line Sensor Failed.
How do I reconnect my thermostat to my boiler?
How long does Salus take to pair?
Gently press and hold the SYNC button with a blunt object. After 3 seconds the Boiler Control LED will flash once every second to indicate it is ready to pair and ready to receive a signal from the thermostat.
How do I pair my Salus rt500rf with a receiver?
How do I connect my Salus thermostat to my boiler?
Why is Salus iT500 offline?
The App says my iT500 is OFFLINE and my iT500 does not have the internet globe indicator on the screen, why is this? Check that you have the power supply turned ON to the gateway and it has a steady green light showing. The green light indicates you are connected to the SALUS server.
How do you bypass a Salus thermostat?
How do I reset my Salus rt520tx?
To reset the thermostat, press MENU, DOWN and BOOST simultaneously for 5 seconds. Repeat the process for all time periods. Once service mode has become active, the device will lock the set point temperature as set by the installer/landlord.
How do I reset my Salus rt310tx?
Press the RESET button once. You can use a paper clip. Your thermostat will be reset and will start up automatically. Remove the batteries without pressing any button.
Why is my wireless thermostat not working?
Check the batteries in the thermostat
Being wireless, the sole power source for the thermostat is its batteries and they don’t last forever. Try changing the batteries and then turn the heating on.
How does a Salus wireless thermostat work?
Senses the air temperature in the room and switches the heating on when the temperature drops below the thermostat setting. Once that temperature has been reached, the heating will turn off. So, as a programmable room thermostat, the Salus RT500RF is a programmer and room thermostat wrapped into one.
How do I turn off the red light on my thermostat?
You can count the number of flashes, usually between two and nine, and then it just repeats itself. You can then reset the system by turning the thermostat “off”, waiting thirty seconds then turning it back on again. This should restart the system, but it may take up to 10 minutes for the outdoor unit to start up.
How do I reset my thermostat?
Here are the step-by-step reset instructions:
- Turn your thermostat off by switching it to the off position.
- Find the breaker that powers your HVAC system and turn it off.
- Wait 30 seconds and turn the breaker back on.
- Turn your thermostat back on.
Why is my heat on light blinking?
If you see a flashing light on your thermostat, that’s a signal that there’s a problem with your outdoor unit. When this happens, your outdoor unit will shut off and send a signal to your thermostat, causing it to blink. Thing is, that signal doesn’t mean your indoor unit is made aware of the problem.
Why wont my Salus thermostat connect?
If the RED and GREEN LED’s on the receiver are NOT flashing, you will need to Re-Pair the Thermostat and Receiver. To do this, slide the ON/OFF switch on the receiver to OFF and then slide it back to ON. The RED LED will now flash. Now, enter the pairing process by choosing Menu > Pairing > PAIR.